Retrofits & Upgrades

With the Bag Top Trimmer located at the top sealer entry, the production run sometimes needed to be stopped to remove...

Due to constant strain, the pressure pulleys were prone to wear out and require frequent replacement.

Constant demands on the lifting jacks of the conveyor would cause premature damage and need replacing.

The previous heating bar design required regular maintenance that, if not performed affected the strength of the seals

Due to constant wear and tear, the top sealer pulleys needed to be replaced on a regular basis.

Film roll changeovers forced the halt of production. Frequent film roll changeovers were required because the bagger could not support larger rolls.

Product could build up inside the V-groove of the pulleys causing the belts to come loose thus stopping production.

The Size-Adjustable Filling Chute can replace up to 3 filling chutes with a single pneumatic one...

Our newly designed laths made of stainless steel and hardened by thermal treatment are the longest lasting laths available on the market...

Although effective, the seal created by the knurled rollers was not always aesthetically pleasing and could lack strength.

The Top Sealer Retrofit makes the seal height adjustment very easy to do, thanks to...

The Bag Alignment Guide retrofit allows the operator to make automatic and accurate adjustments of the guide...

Premier Tech designs customized grippers to fit your needs in constant evolution.  We have the ability of designing custom grippers such as...

This retrofit has been specifically developed to support heavy-duty pallets such as CHEP pallets. Its updated design minimizes fork deflection...

Obsolete CRT design is large and creates heat in enclosure. Keypad is also obsolete...

In the previous design, solid end caps allow product to be trapped in the cartridge sleeve area. This trapped product can cause the anvil to overheat and prematurely wear out.

The Red Valve can be difficult to install without damaging the internal bladder. When damaged, the bladder is expensive to replace.

The Branson 900DA and 921AO power supply and actuator are obsolete – no longer available! If either one fails, both must be...

With the updated design, springs are added to ensure that the pinch tube stays closed; they effectively block the product pressure...

The NXT Conversion Kit converts an existing DM / MP / E / DD weight controller style to a fully electronically weight controlled filler. 

With the updated design, the llat LCD provides crisp, clear, color display of bag weight and other control information...

Previous fluidization doors did not come equipped with a diffuser door. This can produce uneven fluidization air throughout the Air Pad.

The NXT Conversion Kit converts the obsolete existing DM weight controller to the current NXT style weight controller.

In most operations, the bag chair must be adjusted for different lengths of bags. This chair is difficult to access and awkward to...

L’opérateur peut régler à distance le mode d’écoulement du produit à partir d’un clavier. L’actuateur servocommandé déplace avec exactitude...

With the new design, two laser sensors detect that the bag is properly positioned for clean and accurate filling...

The original 900 Series Actuator and its spare parts have become discontinued as they are no longer manufactured...

Dual suction cup arrangement with 4-bar linkage provides superior valve opening performance.

With the presivous design, the scale isolation gap at packer post can result in weak dust collection flow. 

The NXT Conversion Kit converts an existing mechanical filler to a fully electronically weight controlled filler. 

The NXT Conversion Kit converts the obsolete existing DM weight controller to the current NXT style weight controller used on Stonepak Checkweighers. 

Thanks to the updated design, the motor drive assembly with VFD controller provides smooth, consistent operation at rates up to 12 bags...

The original design used a Georgia Kobold two speed motor or an Allen Bradley Servo Drive system. Both designs are discontinued.

The SEW Eurodrive Movidyn servo controller is obsolete and no longer available.

The MP weight controller includes an upgrade to solenoid operated air valves...

The DM weight controller provides a digital display of the bag weight.

It is possible to retrofit a Robotic Valve Bag Handling Equipment to your current STONEPAK valve bag filling systems.

Some Allen Bradley 1305 & 1336 drives are now discontinued. Those drives were used by the Premier Tech Chronos’ AP Series...

The new Panel View (PV-600 +) supports 3 different languages (English, French and Spanish) that can be swapped at any time from...

This retrofit has been specifically developed to support heavy-duty pallets such as CHEP pallets. Its updated design minimizes fork deflection...

The palletizer has to be stopped every time a motor overload reset is required, as the reset button is located inside the electrical panel...

With the previous design, the drive parameters adjustments are made through a touchscreen inside the electrical panel...

In the previous design, none of the elevator components (guiding wheels, the elevator frame, or conveyor) are detachable from... 

The Motorized Height Adjustment System replaces the manual version for an easy and quick adjustment of the lower conveyor...

The motorized centering device automatically adjusts the centering guides each time... 

With chains and springs to open and close the flaps, the previous design is less durable than the updated version.

Over time, cracks can appear on the elevator conveyor, which may result in the replacement of the whole module...

This retrofit enables you to place a cardboard slip sheet on an empty pallet or between... 

The new slip sheet dispenser has 2 multi-bellow vacuum pads that lift both ends of the slip sheet higher than...

The AP Series Software Retrofit will give additional options, greater reliability and improved production rates...

Obsolete CRT design is large and creates heat in enclosure. Keypad is also obsolete...

The NXT Conversion Kit converts an existing DM / MP / E / DD weight controller style to a fully electronically weight controlled filler. 

With the updated design, springs are added to ensure that the pinch tube stays closed; they effectively block the product pressure...

Previous fluidization doors did not come equipped with a diffuser door. This can produce uneven fluidization air throughout the Air Pad.

In most operations, the bag chair must be adjusted for different lengths of bags. This chair can be difficult to access and awkward to adjust.

The Red Valve can be difficult to install without damaging the internal bladder. When damaged, the bladder is expensive to replace.

With the updated design, the llat LCD provides crisp, clear, color display of bag weight and other control information...

With the updated design, the operator can adjust the dribble position from a remote keypad...

The DM weight controller provides a digital display of the bag weight.

The MP weight controller includes an upgrade to solenoid operated air valves...

With the new design, two laser sensors detect that the bag is properly positioned for clean and accurate filling.

The NXT Conversion Kit converts an existing mechanical filler to a fully electronically weight controlled filler. 

Dual suction cup arrangement with 4-bar linkage provides superior valve opening performance.

Thanks to the updated design, the motor drive assembly with VFD controller provides smooth, consistent operation at rates up to 12 bags...

The original design used a Georgia Kobold two speed motor or an Allen Bradley Servo Drive system. Both designs are discontinued.

The SEW Eurodrive Movidyn servo controller is obsolete and no longer available.

The original 900 Series Actuator and its spare parts have become discontinued as they are no longer manufactured...

In the previous design, solid end caps allow product to be trapped in the cartridge sleeve area. This trapped product can cause the anvil to overheat and prematurely wear out.

With the presivous design, the scale isolation gap at packer post can result in weak dust collection flow.

The Branson 900DA and 921AO power supply and actuator are obsolete – no longer available! If either one fails, both must be...

The NXT Conversion Kit converts the obsolete existing DM weight controller to the current NXT style weight controller.

The NXT Conversion Kit converts the obsolete existing DM weight controller to the current NXT style weight controller used on Stonepak Checkweighers. 

The existing hoist idler mounts do not provide shock absorption during a jamb event or provide constant tension on the chain to prevent the chain...

All of these can be added to your machine for additional safety
and OSHA compliance.

Retrofit your existing SPLX or SPLX MKII with a new MKII side mounted case turner. This new turner replaces the original side turner that...

This Engineering Bulletin is to inform Premier Tech Chronos customers that it is possible to retrofit your existing SPLX with a new MKII rake...

Guarding of areas that, in the past, were not covered, but are necessary to have occasional access, can be taken care of by adding fences and...

Retrofit your existing SPLX or SPLX MKII with a new MKII lift up rake with the new cam follower bearing design. This new rake replaces the...

Retrofit the original chain-to-chain sprocket driven live roller to a belt driven live roller for the SPLX & LoPal models.

Retrofit the original chain-tochain sprocket driven live roller and rake to a belt driven live roller and overhead rake for the P7500 and P7900 models.

Retrofit the hydraulic motors for series P7500 and P7900 with all electric drive motors. This conversion from hydraulic to electric will replace...

Enhance your packaging machine by migrating your graphic display to the new PV-Plus 6 700. Its operator terminal is ideal for applications that require...